Ir para o conteúdo 
Escolhendo o caminho certo vacuum circuit breaker mounting configuration is one of the earliest and most consequential decisions in any medium-voltage (MV) switchgear project. The mounting method you select drives footprint, maintenance strategy, personal safety during service, and total cost of ownership. This guide explains the two dominant families—fixed e withdrawable (also called drawout or truck-type) vacuum circuit breakers (VCBs)—walks through indoor VCB installation requirements, and gives you a practical checklist for how to specify the correct unit for your switchgear.
Whether you are an EPC engineer, a panel builder, or a utility specifier, the goal is the same: match the breaker’s mechanical arrangement to how the installation will actually be operated and maintained over the next 20–30 years.
A vacuum circuit breaker mounting configuration describes how the VCB is physically positioned, secured, and connected inside its switchgear cubicle. “Mounting” is not just about bolting a device to a frame—it defines how the breaker connects to the busbar and cable terminations, how it is isolated for maintenance, and what happens to the rest of the substation when the breaker is removed.
In modern indoor MV switchgear, almost every VCB falls into one of two mechanical arrangements:
The simplest way to understand the trade-off is to compare them side by side. A fixed vacuum circuit breaker is built for simplicity and cost; a withdrawable VCB is built for serviceability and safety.
| Aspecto | Fixed-Type VCB | Withdrawable (Drawout / Truck-Type) VCB |
|---|---|---|
| Breaker position | Bolted and wired directly into the cubicle | Mounted on a movable truck with connected / test / disconnected positions |
| Maintenance access | Whole cubicle must be de-energized | Breaker withdrawn to test/disconnected; busbar can stay energized |
| Personnel safety | Lower—live parts exposed when front cover opened | Higher—isolating shutters cover fixed contacts automatically |
| Footprint & cost | More compact, lower capital cost | Larger cubicle, higher capital cost |
| Typical application | Compact substations, ring main units, fixed-switchgear lines | Critical feeders, frequent-maintenance sites, important transmission nodes |
In a fixed arrangement, the fixed vacuum circuit breaker is secured to the cubicle structure by bolts, and its primary terminals are connected with rigid busbars or flexible conductors. There is no movable truck and no separate test position. To inspect or replace the breaker, the entire cubicle—and often the adjacent busbar section—must be isolated and earthed.
Fixed mounting is the right choice when capital cost and panel depth are constrained, and when the feeder does not require frequent breaker withdrawal. Chuanli’s ZN63A(VS1)-12 indoor vacuum circuit breaker is a representative fixed-type unit widely used in 12 kV indoor installations, with a compact footprint suited to fixed cubicles.
A withdrawable VCB—often described in specifications as a VCB drawout ou VCB truck type—is housed on a wheeled truck inside an armored cubicle. The truck moves along guide rails between three defined positions:
This arrangement is the foundation of armored withdrawable switchgear such as the IEC 62271-200 metal-clad design. It lets a maintenance team pull a breaker for inspection while the rest of the switchboard remains energized—a major safety and uptime advantage. Chuanli’s KYN28-12 armored withdrawable switchgear is a classic drawout solution where the VCB sits in a dedicated truck-type compartment.
Correct indoor vacuum circuit breaker mounting is what turns a datasheet into a safe, serviceable installation. Before any breaker is lifted into its cubicle, confirm the following:
Um típico VCB installation sequence for a withdrawable unit is:
For panel builders integrating complete lines, our range of medium-voltage switchgear cabinets is engineered to accept both fixed and withdrawable VCB formats with standardized mounting interfaces.
Specifying the right unit means translating the application into a short, unambiguous list of parameters. Use this checklist when you issue a enquiry or datasheet:
| Parâmetro | What to define |
|---|---|
| Rated voltage & insulation | 12 kV, 24 kV or 40.5 kV; power-frequency & lightning impulse levels |
| Rated normal & short-circuit current | Rated current (630–4000 A) and breaking capacity (IEC 62271-100) |
| Mounting type | Fixed, or withdrawable (drawout / truck-type) with required positions |
| Internal arc classification | IAC rating and access zone (IEC 62271-200) if required |
| Control & protection | Trip coil, protection relay, and communication interface |
| Mechanical endurance | Number of no-load operations expected over service life |
If you are still deciding between arrangements, browse the full portfolio of Disjuntores a vácuo para ambientes internos and match the rated current, breaking capacity, and mounting format to the cubicle you have selected.
Our medium-voltage engineering team helps EPCs and panel builders select between fixed and withdrawable VCB formats, validate clearances, and integrate breakers into armored switchgear. Send us your single-line diagram and rated parameters—we will return a mounting and specification recommendation.
A fixed VCB is bolted and hard-wired into the cubicle, so the whole cubicle must be de-energized for breaker work. A withdrawable VCB sits on a movable truck and can be rolled to a test or disconnected position, letting the busbar stay live while the breaker is serviced.
These are alternative names for a withdrawable VCB. “Drawout” refers to the breaker being drawn out of the cubicle on its truck; “truck-type” refers to the wheeled carriage that carries the breaker between connected, test, and disconnected positions.
After the cubicle is leveled and anchored, connect the busbar and cable terminations to the fixed side, insert the breaker truck on its rails, verify seating and interlocks, then perform insulation-resistance and contact-resistance tests before energization. Always follow the manufacturer’s installation manual and IEC 62271-200.
Choose fixed when footprint and capital cost are the priority and frequent breaker withdrawal is not expected. Choose withdrawable when maintenance access, personnel safety, and minimum downtime matter more than first cost—typical for critical feeders and important nodes.
Clearances follow the breaker’s rated voltage and the applicable standard (e.g., IEC 62271-1). Minimum phase-to-phase and phase-to-earth distances, cubicle depth for truck travel, and foundation/anchor details are given in the manufacturer’s mounting drawing and must not be reduced on site.
Define rated voltage and insulation level, rated normal and short-circuit current, mounting type (fixed or withdrawable), internal arc classification if required, control/protection interface, and mechanical endurance. Use the checklist in the “How to Specify” section above as your enquiry template.
Generally no—fixed and withdrawable breakers use different cubicle structures, rail/truck interfaces, and isolating arrangements. A withdrawable VCB requires a cubicle designed for truck travel and shutters; a fixed breaker requires a cubicle with hard-wired primary connections. Specify the cubicle and breaker as a matched pair.
Continue your specification research with these related guides:
This guide is prepared by the Chuanli Electric medium-voltage engineering team, drawing on IEC 62271-100 and IEC 62271-200 practice. It is for general technical reference; always confirm details against the specific product manual and local regulations before procurement or installation.
